Technics offers a variety of carts to
increase gel coat application efficiency by
positioning molds for quick, easy spray
coverage. Hinged top conveyor frame tilts
forward for spraying vanity and panel molds.
Rotating center plates raises tub molds up
for spraying.
All carts feature spray guard protection
covers over hand controls, power components,
and critical points of movement. Air over
hydraulic power system uses in plant
compressed air to pressurize a hydraulic
reservoir. Unlike air pressure, hydraulic
pressure does not compress so lifting and
tilting actions of Technics Gel Spray Carts
are smooth and controllable instead of bumpy
and hard. All carts rated for use in
hazardous areas.
|
Tilt-Rotate Gel Spray Cart
TILTING-ROTATING STYLE, TILTED |
|
TILTING-ROTATING STYLE, ROTATING
PLATE RAISED |
|
Construction: |
Mig welded steel base frame for
strength and rigidity.
Adjustable legs for leveling
cart. Bronze bushings at pivot
points and hydraulic cylinder
mounts.
Galvanized steel spray guard
located inside top conveyor
frame protects all critical
components from over-spray.
Additional spray guards protect
operating controls and carriage
assemblies. |
|
Welded push handle. Enamel
painted MarMax green. |
|
|
Carriage Assembly |
Machined steel 4 dia. V-guide
wheels with zerk style grease
fittings and replaceable needle
bearings. |
|
Service: |
|
Fixed level service height, 29
adjustable 27 3/4 to 30 1/2 |
|
Fixed level service height, 27
adjustable 25 3/4 to 28 1/2 |
|
Tilt service, controllable
position up to 30 degree forward
tilt |
|
Rotate service, up to 2 lift,
360 degree unrestricted rotation |
|
|
Conveyor Frame: |
20 1/8 c.c. conveyor wheels on
6 centers. Standard length:
144.
Non-standard widths and lengths
available. |
|
Power System: |
|
Hand operated, air activated
hydraulic system, hydraulic pump
with 80 cu. in. reservoir oil
capacity, two stage release
mechanism and hydraulic flow
control valves reduces shock on
system while allowing for fast
or metered down flow. Hand
operated directional control
valve safely allows operation of
only one function (tilt or
rotate) at a time and allows
positive holding of mold
position for spraying. |
|
Operates on 60 psi in plant
compressed air supply. |
|
No electrical connection
necessary, hazardous area
operation approved. |
|
|
Hi/Low
Elevating Gel Spray Cart with Tilt-Rotate
Features
Hi/low gel spray carts incorporate the
same tilt and rotate features of our
standard gel spray carts plus the ability to
raise or lower molds for a better spraying
position and increased efficiency of gel
coat application. Positive holding controls
assure mold remains in position though out
duration of gel coat application. |
|
HI/LOW GEL
SPRAY CART, TILTED |
|
HI/LOW GEL
SPRAY CART, LOWERED W/ ROTATING PLATE RAISED |
|
Construction: |
Mig
welded steel base frame for
strength and rigidity. Dual
scissors arms with adjustable
tie rods. Bronze bushings at
pivot/rotation points and
Hydraulic cylinder mounts.
Galvanized spray guards protect
hydraulic components, operating
controls, and carriage
assemblies. Hinged top
frame with overspray guards and
welded push handle. Enamel
painted MarMax green. |
|
Carriage Assembly |
Independently adjustable
carriages with overspray guards
for leveling base frame.
Machined 4 dia. V-guide wheels
with zerk style grease fittings
and replaceable needle bearings. |
|
Service: |
|
Vertical travel 18 to 31 |
|
Tilt
service, controllable position
up to 30 degree forward tilt |
|
Rotate plate service, 2 lift,
360 degree unrestricted rotation |
|
|
Conveyor Frame: |
20 1/8 c.c. conveyor wheels on
6 centers. Standard length:
144.
Non-standard widths and lengths
available. |
|
Power System: |
Two
independent air over hydraulic
up/down and tilt or rotate
operating systems, each with 80
cu. in. reservoir oil capacity,
two stage release mechanism and
hydraulic flow control valves
reduce shock on system while
allowing for fast or metered
down flow. Hand operated
directional
control valve safely allows
operation of only one function
(tilt or rotate) at a time.
Independent up/down control
permits raising or lowering
molds in any position.
|
|
No electrical connection
necessary, hazardous area
operation approved. |
|
|
